HI Phil first rodeo here but i have been a lurker for sometime. I am allowing enough funds to purchase upto 6 x s21 235th , i know that it has been done lots with s19s from research however one of the suppliers told me that the S21 do not like being submerged and this will put a spanner in the works for me Immersion is the only way for me to go as i have to keep the noise and internal heat to absolute minimum even in an outbuilding. I have access to an size of automotive/commercial truck type radiator for the outside cooler part. My good friend can tig weld and i have a spare few sheets of 3mm aluminmum for the tanks. Then its just a case of adding pipe work for the circuit, pump and enough bitcool for immersion. I have a 32 amp and 68 amp it armor cable going out to the out building already in trench etc, i just need to finish the MCB on opposite end. Ethernet connections all ready to connect Originally i was going to use the radiators as a heat exchanger type set up to dump the heat into a pool, however thinking about it i dont think it will work so well. If you want to keep the bitcool at 25 degrees max then that is not going to be a very warm pool. At 35 degrees i think the miners loose some efficiency. So i either submerge the radiators in a constant cold sub 15 degree supply of fresh water, or i have to run fans on the radiators to dump the heat into the atmosphere? Are you doing any immersion cooling with S21?
HI Phil first rodeo here but i have been a lurker for sometime. I am allowing enough funds to purchase upto 6 x s21 235th , i know that it has been done lots with s19s from research however one of the suppliers told me that the S21 do not like being submerged and this will put a spanner in the works for me Immersion is the only way for me to go as i have to keep the noise and internal heat to absolute minimum even in an outbuilding. I have access to an size of automotive/commercial truck type radiator for the outside cooler part. My good friend can tig weld and i have a spare few sheets of 3mm aluminmum for the tanks. Then its just a case of adding pipe work for the circuit, pump and enough bitcool for immersion. I have a 32 amp and 68 amp it armor cable going out to the out building already in trench etc, i just need to finish the MCB on opposite end. Ethernet connections all ready to connect Originally i was going to use the radiators as a heat exchanger type set up to dump the heat into a pool, however thinking about it i dont think it will work so well. If you want to keep the bitcool at 25 degrees max then that is not going to be a very warm pool. At 35 degrees i think the miners loose some efficiency. So i either submerge the radiators in a constant cold sub 15 degree supply of fresh water, or i have to run fans on the radiators to dump the heat into the atmosphere? Are you doing any immersion cooling with S21?

HI Phil first rodeo here but i have been a lurker for sometime. I am allowing enough funds to purchase upto 6 x s21 235th , i know that it has been done lots with s19s from research however one of the suppliers told me that the S21 do not like being submerged and this will put a spanner in the works for me Immersion is the only way for me to go as i have to keep the noise and internal heat to absolute minimum even in an outbuilding. I have access to an size of automotive/commercial truck type radiator for the outside cooler part. My good friend can tig weld and i have a spare few sheets of 3mm aluminmum for the tanks. Then its just a case of adding pipe work for the circuit, pump and enough bitcool for immersion. I have a 32 amp and 68 amp it armor cable going out to the out building already in trench etc, i just need to finish the MCB on opposite end. Ethernet connections all ready to connect Originally i was going to use the radiators as a heat exchanger type set up to dump the heat into a pool, however thinking about it i dont think it will work so well. If you want to keep the bitcool at 25 degrees max then that is not going to be a very warm pool. At 35 degrees i think the miners loose some efficiency. So i either submerge the radiators in a constant cold sub 15 degree supply of fresh water, or i have to run fans on the radiators to dump the heat into the atmosphere? Are you doing any immersion cooling with S21?

HI Phil first rodeo here but i have been a lurker for sometime. I am allowing enough funds to purchase upto 6 x s21 235th , i know that it has been done lots with s19s from research however one of the suppliers told me that the S21 do not like being submerged and this will put a spanner in the works for me Immersion is the only way for me to go as i have to keep the noise and internal heat to absolute minimum even in an outbuilding. I have access to an size of automotive/commercial truck type radiator for the outside cooler part. My good friend can tig weld and i have a spare few sheets of 3mm aluminmum for the tanks. Then its just a case of adding pipe work for the circuit, pump and enough bitcool for immersion. I have a 32 amp and 68 amp it armor cable going out to the out building already in trench etc, i just need to finish the MCB on opposite end. Ethernet connections all ready to connect Originally i was going to use the radiators as a heat exchanger type set up to dump the heat into a pool, however thinking about it i dont think it will work so well. If you want to keep the bitcool at 25 degrees max then that is not going to be a very warm pool. At 35 degrees i think the miners loose some efficiency. So i either submerge the radiators in a constant cold sub 15 degree supply of fresh water, or i have to run fans on the radiators to dump the heat into the atmosphere? Are you doing any immersion cooling with S21?